Reseeding: an overview
Reseeding may seem like an inconvenience, a cost you don’t need or even just a waste of time but silage and grazing swards that contain high levels of weed are losing you money. They are low yielding and produce lower quality silage and grazing grass.
Reseeding should be given strong consideration when any of the following features become evident in a sward:
- High content of weed grasses e.g. scutch, bent grass
- Low ryegrass content
- High content of broad-leaved weeds e.g. chickweed, docks, thistles and buttercups
- Reduced milk yield or live weight gain
- Poor re-growth following grazing or cutting
- Bare patches throughout sward
- Reduced silage DMD values
In general, swards cut twice annually for silage should be reseeded every five to eight years. For grazed swards, the arguments for reseeding lie in an extended grazing season, improved re-growth and the continued improvement in yield and quality achieved by the breeding of new ryegrass varieties.
Advantages of reseeding
- Increased sward productivity (+15-20% especially in the shoulder periods)
- 8% higher milk output/ha relative to permanent pasture
- Use of newer grass varieties
- Reduced silage requirement
- Swards which respond better to applied nitrogen, higher carrying capacity
- Improved grass qualities
Timing
Swards can be reseeded any time between April and October, provided weather conditions are favourable for good emergence and establishment. Grass seeds have a small energy reserve, which means seedlings won’t last long in periods of cold weather or drought. Germination and establishment improve dramatically once temperatures rise above 10-12°C. Moisture availability is extremely important and reseeding during midsummer may be problematic for this reason. Timing of sowing clover is even more important. To guarantee good germination and establishment, sow clover by the end of August at the latest.
Methods
A number of different methodologies for sowing grass seed are available. These will vary in cost and also their suitability in different situations. Factors such as cost, soil type, elevation, slope, availability of certain machinery and the nature of the existing sward will influence the choice of method used. However, whichever method is used, it must provide for good contact between soil and seed, as this is the over-riding factor in achieving satisfactory germination and establishment. Some of the main methods used are summarised below:
- Plough, Till and Sow:
- Traditionally the most common method used for reseeding in Ireland
- Most consistent and certain method of establishing a vigorous and healthy sward
- Ploughing offers certain advantages such as burying weed seeds, creating a debris-free seedbed and ease of tilling
- Deep ploughing should be avoided - the fertile top layer of soil will be buried too deep
- Considered expensive but generally provides good seedbeds resulting in good germination and establishment
- Minimal Cultivation:
- Originally used in areas where ploughing was difficult or undesirable, but has grown substantially in popularity in recent years
- Uses a power harrow, rotavator or similar type machine to cultivate a shallow seedbed
- It is important to have relatively low levels of debris or stubble and to achieve very good consolidation of the seedbed through rolling
- Direct Seeding:
- Specialised drilling machines cuts a slot in the soil into which the seed is dropped
- You should spray off existing sward well in advance with glyphosate
- Mow as bare as possible to give the new seedlings a chance to establish through the existing sward stubble
- Sow sward in two directions to increase the chances of success
Whatever method of actual sowing you use, keep in mind these good management practices pre- and post-sowing:
Sward desiccation
Spraying the existing sward with glyphosate (e.g. Roundup Gold, Touchdown, Rosate 36) in advance to remove weeds. No weeds mean easier ploughing and tilling and less cloddy seedbeds.
When glyphosate spraying remember:
- Good growing conditions are essential
- Sward cover should be 10 -15 cm
- Leave adequate periods between spraying and ploughing (7-10 days) or spraying and tilling (14 - 21 days)
- Different formulations are available - check label
- Use sufficiently high rate to kill strong weeds e.g. docks
- Do not use contaminated water from rivers, streams, lakes
Fertility maintenance/improvement
We strongly recommend testing your soil to determine soil fertility. If lime is required, apply it pre-sowing and work into the top 10 - 15 cm of soil. If you are direct seeding we strongly recommend liming regardless of soil fertility status. This will combat the harmful effects of decaying vegetation. Granular lime products allow great flexibility around sowing time. In the absence of a soil test, apply a basic dressing of three to four bags per acre of a balanced fertiliser such as 10.10.20 at sowing. Tailor fertiliser application to the requirements of under-sown crops.
Last updated 30th August 2016